3 Ways The Ghost Immobiliser Install Can Influence Your Life
Autowatch Ghost Immobiliser Installation
The Ghost is the most advanced aftermarket in the UK. immobiliser for CAN bus. It's discreet, doesn't use key fobs or LED indicators and is concealed within the wiring of the vehicle.
It also allows the user to temporarily disable the system by using Transport Mode for when they are renting out their vehicle. This guide will guide you through the steps of installing a Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a modern security device that guards your vehicle from hacking, key cloning and relay attacks. The system is connected directly to the ECU of your vehicle and protected by a pin code you set. It is inaccessible to thieves using diagnostic scanners and other modern methods. It isn't able to be disabled using circuit cuts.
The system is simple to use, however professional installation is recommended to ensure a smooth connection with the ECU of your vehicle. Installers who are approved by Thatcham can assist with the installation and programming of your Ghost system. They can also suggest a tracking device or alarm system to complete your vehicle's protection package.
To prevent an accidental deployment of short circuits or airbags The installer must first disconnect your battery. Once the battery is disconnected, the installer can safely begin working. Basic hand tools can be used to ensure precise connections. ghost 2 immobiliser problems The Keylab can be used to verify electrical values. Cable tie and insulation tape are essential to protect connections and keep wiring tidy. In addition, the user's manual offers specific instructions specifically tailored to your Ghost Immobiliser model.
During the installation, it is crucial to select the right grounding location that is free of paint and debris. Installers must also ensure that the immobiliser's wires CAN H & CAN L are connected to the proper ECU ports. These wires can be plugged into or soldered depending on the model. Using a top-quality connector is recommended to ensure a durable and reliable connection.
Transport Mode can be turned on by the customer after the installation is complete. This allows mechanics or valet parking to use the vehicle without having to know the pin code. The customer has to press the service icon on the dashboard five times within 2 seconds. The system will confirm this by showing 5 indicators.
The Autowatch Ghost 2 immobiliser is TASSA approved and is a highly efficient immobiliser. It's an excellent choice for those who rent out their vehicles regularly on platforms like Turo. An immobiliser can cut down on insurance costs, since it decreases the likelihood of theft.
Getting Started
It's not difficult to come up using an autowatch immobiliser in order to guard your car from thieves. It prevents your car from running even if someone steals or copies your key. It's possible due to its advanced technology that stops the engine from starting until the correct PIN code is entered.
The device is connected to the vehicle's bus system CAN and allows direct communication with the ECU. It uses existing buttons on the dashboard and steering wheel to create a unique sequence that only you can identify which makes it impossible for someone else to start your car. This is the most secure way to protect your pride and joy. It will ensure that your car's value remains intact if you ever want to sell it.
Installing a ghost immobiliser can be an easy procedure, but it is important to follow the instructions carefully to avoid issues with electricity and system malfunctions. First, you need to locate and determine a constant 12V power source as well as an appropriate grounding point on the chassis of your vehicle. Then, you can begin connecting the wires to the immobiliser. Make sure you use top-quality connectors and soldering techniques to ensure a solid connection. Also, ensure that you cover the connections with heat shrink tubing or insulation tape to shield them from electrical short circuits and other problems.
After the wires are connected, you are able to connect the battery and begin the engine to check whether the immobiliser works. After you've verified that everything is working properly and you are satisfied, you can place the immobiliser in a secure place inside the vehicle. Be sure to cover it properly to stop any thief from taking advantage of it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) certified This means it is in compliance with the highest standards of security and is a great protection against car thieves. It offers superior protection against key cloning, hacking, and relay attacks. It isn't able to be disabled unless you know the code. The device is easy to use, and it can be set up to an option for a service valet so that your vehicle will not be activated if you bring it for an MOT or servicing.
Wiring
The Ghost Immobiliser, a cutting technological security system, has been designed to prevent vehicle theft. It communicates with your vehicle's ECU and directly connects to the CAN bus. In contrast to other aftermarket systems that require the removal of circuit components The Ghost Immobiliser does not interfere with the factory settings for your vehicle.
It's also undetectable to thieves using diagnostic scanners. This is due to the fact that it doesn't send and receive radio frequency signals and it utilizes the CAN data to communicate with your ECU. It doesn't even require any modifications to your current key fobs.
Enter the sequence to disarm (either two or one buttons) and turn on the ignition in your car to use Ghost Immobiliser. The indicator will flash twice to verify that you've entered the correct code. After this, you can start your vehicle and drive off safely.
Once installed The Ghost Immobiliser can protect your car from key cloning and hacking while preserving the value of your most prized possession. If you ever have to hand over your vehicle to valet parking or for service The Ghost Immobiliser can be temporarily disabled in Transport Mode.
You'll require a constant power source (12V) in addition to a grounding point to complete the installation of the Ghost immobiliser. Be sure that both are properly insulated and can be touched. It's also recommended to use cable ties to bundle and secure the wires, since this will reduce the risk of tampering by potential thieves. To avoid mistakes, make sure to double-check these points and mark them using a label or tape. It's recommended to examine every connection for signs of wear and tear. Connectors that are loose could cause malfunctions in the system, so make sure that they're firmly in place and securely insulated. Don't forget to test the Ghost Immobiliser after the installation is complete. This will ensure that the unit is functioning correctly and that all connections are safe and well-insulated. If you encounter any issues, make certain to fix them immediately.
Testing
The Autowatch Ghost immobiliser is an innovative vehicle security system that works seamlessly with your car's ECU to stop unauthorised motor starting. Its cutting-edge technology safeguards your car against hacking, key cloning, and other typical tactics thieves employ to steal vehicles. The Ghost also works in conjunction with other alarm and tracking systems to provide the best protection for your vehicle. The Ghost's unique features, coupled with its secluded design, make it a popular option for both car enthusiasts and security conscious drivers.
It is essential to follow the steps of installation to ensure the complete integration of the Ghost Immobiliser. The best place to start is to consult the wiring diagram of your vehicle that serves as a guideline to locate and connecting the necessary wires. You'll need to determine the grounding and power sources. Once these are found, you'll need to mark them so that they're easy to identify when installing. Finally, it's important to use top-quality tools and materials. Hand tools are a must with making precise connections, while a multimeter will check electrical values and ensure safety. Cable tie and insulation tape will ensure that all connections are tidy. A Ghost-specific user manual is also available.
Before proceeding with the installation it is important to test the system by entering the PIN code and then starting the vehicle. This will ensure that the immobiliser works according to plan, and prevents unauthorised vehicle start-ups. It is recommended to complete this procedure regularly as part of your routine inspections of the vehicle to ensure the system is always functioning properly.
After the installation is completed, you can drive your vehicle with confidence. The Ghost will keep your pride and joy safe from would-be thieves and ensure that nobody is able to take off with your vehicle without the proper PIN code. The Ghost can also be paired with a Thatcham-approved tracker to detect any attempts at tampering or theft, allowing you to locate your vehicle in the event of it being stolen.
The Ghost can be used in a variety of vehicles and is compatible with the majority of major brands. Monty's Locksmith can assist you in securing your vehicle with this cutting edge device. Contact us today to learn more about our service and installation options. We are a TASSA registered installer, which assures us that we follow strict guidelines in the installation of our products. This guarantees customers, insurance companies, and law enforcement agencies that all installations are done safely and in a safe manner.